New automatic pasta machine operator features:

    1. The machine should be installed in a dry, airy ground level, to ensure that the machines work smoothly and reliably.

    2. Before use, check the power supply voltage is consistent with the use of the machine; a ground wire core symbol is reliable grounding; turn meets the requirements; installed position shown by cis junction dustpan and dustpan. (For ease of packing and shipping, cis dustpan is not installed on the machine)

    3. noodles: Mix flour with institutional products, when the inverted switch to "down", blender mix the powder inside the bucket starts running after breading flour evenly to play an open feeder switch can be ruled out automatically. (Recommendations noodles noodles knife removed to extend the life of the knife noodles).

    4. Patch processing: the switch to "smooth" the position of the dough piece mechanic, when marinated dough should be kneaded by rolls thick to thin to adjust the roll gap, to come forward into the face thickness of the thickness of 2 to 3 times. After repeated pressure after kneading dough sheet can be increased and chewy texture, are recommended to take full advantage of the machine is kneaded

    Features. Before cutting the dough sheet should be 3 ~ 5mm thick noodles with roll bar after a good backup.

    5. cutting: 1) Install noodles knife: around the grid plate has two flutes, noodles knife into the slot, rear gear noodles on a knife with the large gear meshing, tighten the butterfly nut fixation noodles fixed knife.

    2) Cutter: a spare patch tip his hand into the rotation of the two roll gap, rolling after re-entering the noodle cutter, cut out pasta, falling junction dustpan. The operator should be promptly cut out noodles brought out, disconnect, put drying rack.

    New automatic pasta machine installation and operation:

    1, the mechanical installation necessary flat fixed. Open the side cover, add the oil in a 30 # reducer. Press the ground mark a ground wire.

    2, check all parts of fasteners during transport if there is loosening.

    3, then the power, try reversing, under normal circumstances, the belt press, and then the motor prison guard.

    4, check the site traffic is smooth hole before starting after refueling.

    New automatic pasta machine operations guide:

    1, and the face: face is the first procedure and pasta production, flour noodles into the machine began noodles, according to the provisions of the proportion of about 25% water, start the power, and the surface of the water mix evenly granular ( to use the best) for 10 minutes, may be used.

    2. Adjust: hand wheel to adjust the roll gap, in each group of the roll gap reference data are as follows: (Unit Exception 330 above) during adjustment, tighten or loosen many of the handwheel and sometimes difficult time alignment, the key is to get clear reason, to grasp the patient can stop adjustment when unskilled normal after locking handwheel.

    3, the operation: marinated the flour into the inner surface of the hopper, press the knife blade and the fixed stop plate, you can start running, the third group of the panel to hand down to the next lead group (a plurality of sets analogy) operation is completed .

    New automatic pasta machine safety and maintenance:

    1. Before the operator uses the instructions should be carefully studied, in strict accordance with the instructions.

    2. This machine is strictly prohibited reversed.

    3. Check all parts before starting any abnormal phenomenon, identify problems and timely treatment to avoid accidents.

    4. prevent iron or other hard substance mixed with flour, so as not to damage the parts.

    5. The back surface can not be poured directly into the inner surface of the bucket.

    6. The machine is prohibited during operation reach into the dangerous parts of the rollers, gears, chains, cutter and so on.

    7. ensure that all moving parts lubricated with oil standard, oil cup, gear, each part of the chain hole, filling the second class 20 # -30 # oil, cutter surface, roll surface finish after class , add a little oil.

    8. Single head (type 60, 80) rolling mill, noodles joint machine clutch clutch must be carried out in a down state.

    9. pressure before idle for 10-15 minutes, when in winter indoor temperature is kept above 10-15 degrees.

    10. Stop keeping machinery clean, no residual in each roll, no face blank.

    11. Keep the gears, lubrication of rolling bearings.

    12. The non debris falling into the other hard rolls and gear.

    13. Every six months to replace the bearing grease.

    14. The non-surface nip adjusted to 5 mm or more running.